
Your furnace isn’t heating. Start here.
A furnace that won’t heat is stressful, especially in a Michigan winter. Before you call anyone, there are five quick checks you can safely do yourself. They take about a minute, and they fix the problem more often than you’d think.
Call us right away at (616) 243-1914 if the house is getting cold fast, if pipes could freeze, or if you smell gas. We answer the phone 24 hours a day, 7 days a week. Regular service hours are Monday–Friday, 9 AM–5 PM, and 24/7 emergency service is available.
The 60-second checks
1. Is the thermostat set to Heat — and above room temperature?
This is the most common cause of a “broken” furnace. Make sure the thermostat is set to Heat (not Cool, not Off), and set the temperature at least 5 degrees above the current room temperature. If the thermostat has a battery, a dead battery can shut the whole system down — try fresh batteries.
2. Is the furnace switch on?
Your furnace has a power switch, usually on the wall near the furnace or on the furnace itself. It looks like a regular light switch. Make sure it’s in the ON position. It gets bumped off by accident more often than people expect.
3. Did a breaker trip?
Check your electrical panel for a breaker labeled “furnace” or “heating.” If it’s in the middle or OFF position, flip it fully off, then back on. If it trips again right away, leave it off and call us — that’s a sign of an electrical problem inside the furnace.
4. Is the gas valve open?
If your furnace runs on gas, find the gas shut-off valve on the gas line going into the furnace. The handle should be in line with the pipe (parallel), not across it. If it’s across the pipe, the gas is off. Turn it so it lines up with the pipe — but only if you do not smell gas. If you smell gas, leave the house and call your gas company or 911. Do not touch any switches or valves.
5. Is the filter clogged?
A dirty filter chokes off airflow. When airflow drops too far, a safety device inside the furnace (a limit switch) shuts the furnace down to protect it. Pull the filter out and hold it up to a light. If you can’t see light through it, replace it with a new one of the same size, then try the furnace again.
If none of these checks brings the heat back, it’s time for a professional. Call (616) 243-1914 or book a service call online.
Common causes when the checks don’t fix it
- Failed igniter. Most modern furnaces light the gas with a hot surface igniter — a small part that glows red-hot. It wears out over time, and when it does, the furnace can’t light at all. This is one of the most common furnace repairs.
- Dirty flame sensor. The flame sensor is a small rod that sits in the flame and tells the furnace the burner is lit. When it gets coated with residue, the furnace thinks the flame went out and shuts the gas off. Cleaning or replacing it is a quick repair.
- Thermostat failure. If the thermostat itself has failed, it may not be telling the furnace to run at all — even if the furnace is fine.
- Tripped safety limit from a dirty filter. A filter that went unchanged for too long can overheat the furnace and trip the safety limit. Replacing the filter sometimes fixes it; if the limit switch itself has failed, it needs replacing.
- Gas supply problem. If the gas is off at the meter, or there’s an issue with the gas supply to the house, the furnace has nothing to burn. If other gas appliances in the house aren’t working either, call your gas company first.
When no heat is an emergency
Call us any time — day or night — if any of these apply:
- A cold snap is coming or underway. Indoor temperatures can drop fast when it’s below freezing outside.
- Pipes are at risk. If the house is cooling toward freezing, water pipes can burst. That’s a far more expensive problem than a furnace repair.
- Elderly people or infants are in the house. They lose body heat faster and can’t always tell you they’re cold.
- You smell gas. Leave the house immediately. Do not turn lights or appliances on or off. Call your gas company or 911 from outside.
For emergencies, see our emergency service page or call (616) 243-1914. Emergency service is $285 for the first hour.
What a no-heat visit costs
A regular residential service call is $180. That covers diagnosis and repair under an hour, excluding parts. If the repair needs a part, we’ll tell you the cost before we install it — no surprises. Emergency service is $285 for the first hour.
What not to do yourself
It’s fine to check the thermostat, the furnace switch, the breaker, the gas valve position, and the filter. Do not open the furnace cabinet, touch gas parts, or work on electrical parts inside the furnace. Gas and high-voltage electrical work inside a furnace is dangerous without training, and a wrong move can create a gas leak or a fire risk. That’s what we’re here for.
Related furnace problems
- Furnace Won’t Ignite? Ignition Failure Repair in Grand Rapids, MI — if your furnace tries to start but never lights
- Furnace Blowing Cold Air? Causes & Repair in Grand Rapids, MI — if air comes out of the vents but it isn’t warm
- Furnace Keeps Turning On and Off? Short Cycling & Intermittent Heat in Grand Rapids, MI — if it heats briefly, then stops, then starts again
- Furnace Repair in Grand Rapids, MI — our main furnace repair page
A-1 Heating & Air Conditioning — Grand Rapids, MI, serving Kent County since 1994. Call (616) 243-1914. We answer the phone 24 hours a day, 7 days a week. Regular service hours are Monday–Friday, 9 AM–5 PM. 24/7 emergency service is available.