Your furnace tries to start but never lights
You hear the furnace click, or the fan starts, but the burners never light — and the house stays cold. That’s an ignition failure. It’s one of the most common furnace problems, and it’s usually a small part that has worn out or gotten dirty.
Call us at (616) 243-1914 if the house is getting cold or you need heat tonight. We answer the phone 24 hours a day, 7 days a week. Regular service hours are Monday–Friday, 9 AM–5 PM, and 24/7 emergency service is available.
How to tell it’s an ignition problem
- Clicking with no flame. You hear a click or a series of clicks, but the burners never catch.
- It tries, then shuts off. The furnace starts up, runs for a few seconds, and shuts down — then tries again. It may repeat this a few times and then stop trying.
- An error code. Some furnaces flash a code on a small light inside the furnace, or show a message on the thermostat. Write down what you see — the code helps us diagnose the problem faster. Don’t open the furnace to look for the light. If your thermostat shows an error message, note it and tell us when you call.
Safe checks you can do
These are the same safe checks that fix many no-heat calls:
- Thermostat: set to Heat, and set at least 5 degrees above room temperature.
- Furnace switch: the switch on the wall near the furnace should be ON.
- Breaker: check your electrical panel for a tripped breaker labeled “furnace” or “heating.” Flip it fully off, then back on. If it trips again right away, leave it off and call us.
- Gas valve: the handle on the gas line to the furnace should line up with the pipe. Only check this if you do not smell gas. If you smell gas, leave the house and call your gas company or 911.
If none of these helps, the problem is inside the furnace — and that’s a job for a professional.
What’s usually wrong
- Dirty flame sensor. The flame sensor is a small metal rod that sits in the burner flame. Its job is to confirm the flame is lit. When it gets coated with residue, it can’t sense the flame, so the furnace shuts the gas off a few seconds after lighting — or won’t light at all. Cleaning or replacing the sensor is a quick, common repair.
- Worn hot surface igniter. Most modern furnaces light the gas with an igniter that glows red-hot, like the element in a toaster. It wears out with use. When it fails, the furnace can’t light the gas at all. This is one of the most frequent furnace repairs we do.
- Gas valve problem. The gas valve controls gas flow to the burners. If it fails, no gas reaches the burners and nothing lights. Gas valve work is strictly professional-only.
- Control board problem. The control board is the furnace’s brain — it runs the start-up sequence. If it fails, the furnace may click, try to start, or do nothing at all. Diagnosing a control board takes testing equipment and training.
What not to do yourself
Do not open the burner compartment. Do not touch gas parts, the igniter, or any electrical parts inside the furnace. The igniter is fragile and runs on high voltage; gas parts can leak if handled wrong. Lighting a furnace by hand is dangerous and should never be attempted. If the furnace isn’t lighting, turn the thermostat down, leave the furnace alone, and call us.
When to call right away
- The house is cooling down and it’s freezing outside.
- The furnace keeps trying to start and failing — repeated failed starts can lock the furnace out, and it will need a professional reset.
- You smell gas. Leave the house and call your gas company or 911 from outside.
What an ignition repair visit costs
A regular residential service call is $180. That covers diagnosis and repair under an hour, excluding parts. If the repair needs a part — an igniter, a flame sensor, a gas valve — we’ll tell you the cost before we install it. Emergency service is $285 for the first hour. You can also book a service call online, or see our emergency service page for after-hours help.
Related furnace problems
- Furnace Not Heating? No-Heat Furnace Repair in Grand Rapids, MI — if there’s no heat at all
- Furnace Keeps Turning On and Off? Short Cycling & Intermittent Heat in Grand Rapids, MI — if the furnace lights, then shuts off right away
- Furnace Blowing Cold Air? Causes & Repair in Grand Rapids, MI — if the fan runs but the burner never fires
- Furnace Repair in Grand Rapids, MI — our main furnace repair page
A-1 Heating & Air Conditioning — Grand Rapids, MI, serving Kent County since 1994. Call (616) 243-1914. We answer the phone 24 hours a day, 7 days a week. Regular service hours are Monday–Friday, 9 AM–5 PM. 24/7 emergency service is available.